

Two-car garage, full-flake system
The slab had oil spots at both bays and a hairline crack at the door. We ground it open, filled the crack, and ran a full-flake system with a sun-stable topcoat.
A garage floor that holds up to Gulf heat, wet mornings, and daily tires — built on a ground slab, not a quick roll.

A garage floor in Crystal River lives a harder life than most. Summer tires come off hot asphalt, morning humidity settles on the slab, and the water table under Citrus County pushes moisture up through the concrete. A floor that skips the prep shows it fast — usually in crescents under the tires, or in bubbles where the slab was damp.
We build floors to hold. Every job starts with a moisture test and a diamond grind that opens the slab so the coating keys into the concrete instead of sitting on it. Cracks get filled, old paint comes off, and the price you get in writing is the price before work starts.
Most of our work is garages, and the garage is where we start. From there the same crew coats the lanai, the pool deck, and the carport — one finish, one crew, one visit where the job allows. Retiree homes here often have all four, and the whole-property job is our signature shape.
Look through the work below, run the calculator for your own floor, and ask for a free in-home estimate. We come look, we test, we measure, and we tell you straight what your floor needs.
Three shapes cover most homes in Citrus County. Find yours and the rest of the page follows it.
Your everyday floor — cars, carts, tools, and storage. A full-flake system with a sun-stable topcoat is the usual pick.
The rooms you live in outside. These floors get bare feet, rain blow-in, chlorine, and full sun — so grip and UV stability are part of the spec.
Garage, carport, lanai, and pool deck in one finish. One crew, one schedule, and a house that reads as one job when you walk around it.


The slab had oil spots at both bays and a hairline crack at the door. We ground it open, filled the crack, and ran a full-flake system with a sun-stable topcoat.


One finish ties the three-car garage to the screened lanai out back. The slab tested damp near the door, so a moisture primer went down first.
The old deck paint was chalky and slick when wet. We stripped it, repaired two settled corners, and coated with grip texture and a sun-stable topcoat.
A working garage that could not sit empty for days. The fast-cure system went down in one visit and the cars were back the next day, per the written schedule.
A home workshop with paint spills and a stained slab. We ground it clean and laid a solid-color epoxy that sweeps out fast after saw work.
A small service shop coated in two phases so work never stopped. The high-build system takes daily lifts, oil drips, and hard cleaning.
The full menu, from the garage to the pool deck. Every service page carries its own price thinking and its own questions.

Full flake broadcast over a ground slab, sealed with a clear topcoat. Our most-chosen garage floor.

Fast-cure, sun-stable coatings for garages that sit in Gulf heat and light.

Peeling kit floors and cracked slabs, ground back and recoated the right way.

The full install, step by step: test, grind, repair, coat, and cure.

Poured metallic finishes with depth and movement. Fit confirmed at the estimate.

Tough, easy-clean floors for shops, stores, and work spaces.

Heavy-build floors for forklift traffic, spills, and daily wear.

Slip-aware, sun-stable deck coatings. Fit confirmed at the estimate.

Screened lanais coated for bare feet, rain blow-in, and daily use.

Covered patios and porches that sweep clean and shrug off storms.

Exterior flatwork coatings for driveways and carports. Fit confirmed at the estimate.

Thin overlays that renew worn concrete without tearing it out. Fit confirmed at the estimate.
Three stages, in plain words. The middle one is the one cheap floors skip.
We measure the floor, check the slab for cracks and old coatings, and test for moisture. In Citrus County the water table sits high, so the test comes first. You get a written price before any work starts.
We grind the whole slab with a diamond grinder to open the pores. Cracks and pits get filled and ground flush. You pick the finish from real samples, in your own light.
The base coat goes down, flake is broadcast by hand until the coat can hold no more, and a clear topcoat seals it. We tell you in writing when you can walk on it and when you can park.
We walk the floor with you, show you how to clean it, and leave the return-to-service times in writing. If a spot needs a touch, it gets done before we leave.
Sweep the grit out, mop with a pH-neutral cleaner, and rinse salt or chlorine off outdoor floors. No waxing, no sealing schedule. The floor is built to be used.
Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.
Rather talk? Call (352) 555-0162.
A two-car garage in our full-flake system runs about $2,750 to $4,300 in our calculator, before slab work. The written price after our visit is the number that counts — the calculator is a planning range.
A flat, dry slab coats fast. A slab with cracks, old paint, or a high moisture reading needs grinding, repair, or a moisture primer first. That work moves the price more than an extra hundred square feet.
With a polyaspartic topcoat, most garages are ready for cars the next day. A full epoxy build takes longer to reach full strength. Your schedule is written down at the estimate, before work starts.
Kit floors peel because the prep is thin — a quick etch over a sealed or dusty slab, with no moisture test. We grind to an open profile, test the slab, and repair it first. That is the whole difference.
Plain epoxy can amber at the garage door line. Our topcoat is UV-stable, so the first few feet inside the door hold their color. That matters most on doors that face the afternoon sun.
The garage has to be empty on install day. Most folks use the driveway and the lanai for a day, or borrow a neighbor's carport. Tell us at the estimate and we will plan the timing around it.
Pick your floor and its size. The range updates as you go.
Add-ons your floor may need
Every floor is different. Slab condition moves the final number more than size does.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.