Free In-Home EstimateLocally Owned & OperatedOne Crew, Start to FinishWritten Price Before Work Starts
Crystal River, FL · Epoxy Floor Installation

Epoxy Floor Installation in Crystal River, FL

The install, step by step — what happens in your garage, in what order, and why each step matters.

Freshly installed epoxy floor in a two-car garage

An epoxy floor installation is a sequence, and the order is the quality. Estimate first, then empty the garage, then grind, then repair, then coat. Skip a step and the floor tells on you — usually months later, in sheets.

Day one is usually prep: the garage is emptied, the slab is diamond ground to an open profile, cracks are filled, and the moisture reading is taken. Day two is coating: base coat, flake broadcast, scrape, and topcoat. The exact split depends on the system and the slab.

Cure times are part of the job, not an afterthought. Polyaspartic-top systems take foot traffic the same evening and cars the next day. A full epoxy build takes longer to reach full strength — about three to four days. Your return-to-service times are written down at the estimate.

The 11 steps, in plain words

Our crew runs the same sequence on every install. It is the trade standard, and it is what keeps a floor down for 15 to 20 years.

  • Estimate visit: measure, read the slab, moisture test, choose the finish
  • Garage emptied by the homeowner
  • Diamond grind to an open profile, with dust extraction
  • Crack, joint, and spall repair, ground flush
  • Vacuum and clean to a dust-free surface
  • Moisture primer where the reading calls for it
  • Base coat at spec thickness
  • Flake broadcast to refusal, by hand
  • Cure, scrape, and vacuum the excess flake
  • Clear topcoat, with grip where the floor gets wet
  • Walkthrough and care instructions in writing

The install in three stages

I

Measure & Test

We measure the floor, check the slab for cracks and old coatings, and test for moisture. In Citrus County the water table sits high, so the test comes first. You get a written price before any work starts.

II

Prep & Design

We grind the whole slab with a diamond grinder to open the pores. Cracks and pits get filled and ground flush. You pick the finish from real samples, in your own light.

III

Coat & Cure

The base coat goes down, flake is broadcast by hand until the coat can hold no more, and a clear topcoat seals it. We tell you in writing when you can walk on it and when you can park.

IV

Walkthrough

We walk the floor with you, show you how to clean it, and leave the return-to-service times in writing. If a spot needs a touch, it gets done before we leave.

Install work, recent

The same Crystal River garage floor before coating
Finished full-flake garage floor in Crystal River
BeforeAfter

Two-car garage, full-flake system

440 sq ft · Final price $3,450

The slab had oil spots at both bays and a hairline crack at the door. We ground it open, filled the crack, and ran a full-flake system with a sun-stable topcoat.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
The same Inverness garage floor before coating
Flake finish carried from a garage into a lanai in Inverness
BeforeAfter

Garage and lanai in one finish

660 sq ft · Final price $5,200

One finish ties the three-car garage to the screened lanai out back. The slab tested damp near the door, so a moisture primer went down first.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Polyaspartic garage floor in Spring Hill

Polyaspartic garage, back fast

440 sq ft · Final price $4,150

A working garage that could not sit empty for days. The fast-cure system went down in one visit and the cars were back the next day, per the written schedule.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.

Get a Free Estimate in Crystal River

Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.

Rather talk? Call (352) 555-0162.

Questions we hear

Why do you test for moisture before coating?

Ground moisture pushes up through the slab. A coating over a damp slab can blister and lift months later. The test tells us whether a moisture primer goes down first — in Citrus County, with a high water table, we test every floor.

What happens if the test reads high?

We prime with a moisture barrier first. It adds cost and a step, and it is the step that keeps the floor down. We would rather tell you that at the estimate than patch a floor later.

How long does a garage take?

Most two-car garages take one to two days of work, depending on the system and the slab. Polyaspartic topcoats cure fast, so cars are usually back the next day. Your written schedule comes at the estimate.

Can you coat over my old epoxy or paint?

Only after it comes off. We grind the old coating away and start from bare concrete. Coating over a peeling layer just gives the new floor something loose to hold onto.

Is it slippery when wet?

Flake texture gives the floor grip, and we add anti-slip grit where the floor gets wet — lanais, pool decks, and garage entries. A smooth gloss finish belongs indoors, not by a pool.

Estimate Calculator

Pick your floor and its size. The range updates as you go.

Add-ons your floor may need

Your planning range —

Every floor is different. Slab condition moves the final number more than size does.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

Call (352) 555-0162 Estimate Calculator