Free In-Home EstimateLocally Owned & OperatedOne Crew, Start to FinishWritten Price Before Work Starts
Crystal River, FL · Garage Floor Repair & Recoating

Garage Floor Repair & Recoating in Crystal River, FL

A peeling kit floor or a cracked slab is not a lost floor — it is a floor that needs the prep done right.

Wide concrete floor with a polished finish

Most repair jobs we see are the same story: a do-it-yourself kit, or a cheap roll-on coat, that looked fine for a season and then peeled in sheets. The cause is almost always the prep — an acid etch over a sealed or dusty slab, no moisture test, and a thin water-based film.

A recoat starts by taking the old floor off. We grind the slab back to bare concrete, chase the cracks and fill them, and test for moisture before anything new goes down. Only then does the new system start.

Limestone bedrock under Citrus County means settling cracks are common, especially on older slabs around Inverness and Crystal River. We fill them and grind them flush, and we tell you straight that a crack can telegraph if the slab moves again — repair hides it, it does not stop the ground from settling.

What we strip and what we keep

Old epoxy, paint, and kit films all come off. Tile and thinset come off too, where a recoat is planned over them. What stays is the concrete itself — we work with the slab you have, and we tell you at the estimate if a slab is too far gone to coat.

  • Full strip to bare concrete, never coat-over-peel
  • Cracks chased, filled, and ground flush
  • Moisture test before the new system starts

How a repair job runs

I

Measure & Test

We measure the floor, check the slab for cracks and old coatings, and test for moisture. In Citrus County the water table sits high, so the test comes first. You get a written price before any work starts.

II

Prep & Design

We grind the whole slab with a diamond grinder to open the pores. Cracks and pits get filled and ground flush. You pick the finish from real samples, in your own light.

III

Coat & Cure

The base coat goes down, flake is broadcast by hand until the coat can hold no more, and a clear topcoat seals it. We tell you in writing when you can walk on it and when you can park.

IV

Walkthrough

We walk the floor with you, show you how to clean it, and leave the return-to-service times in writing. If a spot needs a touch, it gets done before we leave.

V

Care After

Sweep the grit out, mop with a pH-neutral cleaner, and rinse salt or chlorine off outdoor floors. No waxing, no sealing schedule. The floor is built to be used.

Repair work, recent

The same Crystal River garage floor before coating
Finished full-flake garage floor in Crystal River
BeforeAfter

Two-car garage, full-flake system

440 sq ft · Final price $3,450

The slab had oil spots at both bays and a hairline crack at the door. We ground it open, filled the crack, and ran a full-flake system with a sun-stable topcoat.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
The same Inverness garage floor before coating
Flake finish carried from a garage into a lanai in Inverness
BeforeAfter

Garage and lanai in one finish

660 sq ft · Final price $5,200

One finish ties the three-car garage to the screened lanai out back. The slab tested damp near the door, so a moisture primer went down first.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Polyaspartic garage floor in Spring Hill

Polyaspartic garage, back fast

440 sq ft · Final price $4,150

A working garage that could not sit empty for days. The fast-cure system went down in one visit and the cars were back the next day, per the written schedule.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.

Get a Free Estimate in Crystal River

Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.

Rather talk? Call (352) 555-0162.

Questions we hear

Can you coat over my old epoxy?

No — not over a peeling one. We grind the old coating off and start from bare concrete. A new floor over a loose layer just gives the new coat something to peel with.

Will the cracks come back?

A filled crack hides and stays hidden as long as the slab stays still. Limestone settling can move a slab again, and a crack can telegraph through a new coating. We fill it properly and tell you the honest limit at the estimate.

How much does a recoat cost?

The coating itself prices like a new floor — flake runs $6.25 to $9.75 per square foot. Removal of the old coating adds $250 to $700 depending on what is down there. The written price at the estimate covers both.

Is my slab too far gone?

Most are not. Spalls, pits, and cracks are routine repair. A slab that has heaved badly or broken into moving sections may not be a coating candidate — we will say so at the estimate rather than sell you a floor that will fail.

How long does a repair job take?

Usually one to two days of work, plus cure time. The strip and grind is the slow part. Cars are back the next day on most polyaspartic-top systems.

Estimate Calculator

Pick your floor and its size. The range updates as you go.

Add-ons your floor may need

Your planning range —

Every floor is different. Slab condition moves the final number more than size does.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

Call (352) 555-0162 Estimate Calculator